Month: July 2019

Info of Kid’s Room Interior

Decide a theme

One of the crucial decision of all times before starting on with room interiors! Deciding a theme for the room is one of the foremost things you should check and decide with your kid by your side. There are plenty of ideas one can choose from. Choose a colorful, lively, bright and whimsical kind of theme for your kid’s room interior.

Space is what they love most

With the amount of energy, they have in their body, as a parent who would know it better than you. The more space you give the room, the better it is for them. Do make sure while designing the room, you give an ample of space to make the room functional in the most efficient way possible.

Right use of the corners

Your child loves to play with the toys or read books? Well, using the corner of the room for their ‘solace of personal love’ is a right investment. Pick a corner with enough lights and if there is a window nearby, then it makes it even better to use the corners. you may make use of the corner with their favorite books and night lamp and make it as a mini-library. You may use the corner by keeping lots of stuffed toys and make it an in-house play way for them.

Walls or a drawing board?

With a crayon or pen in hand, your child thinks every wall is their canvas. Well, let’s make them feel they are a ‘Picasso’! Provide them a single whole wall to themselves where they can paint or sketch as much as they want to. One day you will find the wall a souvenir of their growing up days.

Hide n Seek: Closet

One of the most important places for a child is his/her closet. Place the closet in the right place with a lot of drawers and hanging space. Make sure you take suggestions from your kid about what kind of closet they wish to have and what kind of styling would they prefer. Adding a little flavor of requirements, you may design the closet, keeping in mind the tone of the theme you are going on with.


About Pole Barn Truss Spacing

Back in the day (early 1990’s) I was on the National Frame Builders Association (NFBA) Board of Directors. One of my fellow board members from the Midwest wanted to take a peek at how pole barns were constructed in the West, so I invited him out for a tour.

After spending a day looking at several of our building projects, his comment to me was, “The inspectors in our area would never let a pole building be constructed with roof trusses placed every 12 feet.”

Twenty years later, I beg to differ. Hansen Buildings has buildings in each of the 50 states and all of them have roof trusses on what my board member friend would describe as being “widely spaced.”

Modern truss design is highly computerized. Enter the span of the truss, bay spacing and load conditions and the engineering programs will design a truss which will meet the design criteria. The lumber and steel plates the trusses are constructed from, have no idea how far apart they are going to be placed. They are inanimate! Yet, somewhere in the deep, dark reaches of history, lies the theory wood trusses must be spaced no more than 24″ on center, or maybe 48″, or perhaps even eight or ten feet? The reality is, there is no magic number.

While H. Howard Doane is credited with being the innovator of the modern pole barn, it was his Agricultural Service farm manager, Bernon Perkins, who is credited with refining the evolution of the modern pole building to a long-lasting structure. It was Perkins who pioneered roof purlins being placed on edge. With this design change, roof trusses could be placed 12 feet apart, making it possible for roofs to support the loads to which they would be subjected.

I’ve had roof truss manufacturers try to convince me it is impossible to place wood trusses at spacings of over every 4 feet. Their defense is, “Our engineers will not allow us to.” The manufacturers of the steel roof truss plates (also referred to as gussets or Gang-nails), provide the engineering design for pre-fabricated wood trusses. Their programs will allow for trusses to be placed on 12 foot or even 16 foot centers, and their engineers will place their engineer’s seal on the drawings to verify.


About Demolition Contractors

Demolishing a properly usually comes with a number of risks. For example, you can be injured by splinter and nails that might be flying around. You can also injure yourself trying to lift items that are too heavy for you.

When you hire a professional contractor you don’t have to go through this. The contractor comes wearing the right gear and with the right machinery thus the work is completed fast and with no injuries at all.

Hiring a contractor also ensures that work is done the right way. For example, if you want to demolish just a part of your property, you can easily bring about the collapse of the entire building because you might not be having the right skills to do the work; however, if you hire a professional, there is no risk of the entire building collapsing.

This is because contractors are usually trained on how to remove the parts that need to go and as a result protect the building from collapsing.

Many contractors offer trash removal services; therefore, when you hire them you don’t have to worry where you will take your trash. The professionals will simply load the trash in their truck and dispose it for you.

To ensure that you enjoy the above advantages of working with a contractor, you should ensure that you consider a number of factors when hiring. One of the factors that you should consider is the ability of the contractor to complete your project fast.

To find if the professional will be able to complete your work within the set time you should ensure that you ask him/her before the work begins. If the professional can’t deliver the work on time you should consider looking for another.

Another thing that you should look out for is the ability of the contractor to handle every aspect of the job. For example, the professional should be able to get the permit authorizing the demolition and at the same time undertake a safe and thorough demolition.


Easily Install Crown Molding

It will help make the spaces between the walls and the ceilings have an even look. Moreover, molding is utilized to finish fireplaces, cabinets, and built-ins.

Installing crown molding is not a new concept. Molding was previously used by homeowners to reflect the room type and its intended purpose.

For instance, reception areas were often furnished with ornate and elaborate moldings while kitchens and other less decorative rooms in the house have plain crown molding.

Generally, it is quite easy to set up. However, you may require the help of a handyman if you intend to install large and complex moldings. Here is a quick guide on how you can install painlessly:

  • Planning
    Most people usually neglect this step. This is a huge mistake since if you don’t plan properly, you may end up being frustrated and may make a mistake while installing it.

There are different types of crown molding. Decide on the specific size and style of molding which you would like to have.

The size should match the ceiling height of your house. Sometimes, you can still opt for large moldings, provided that you properly scale your casings to accommodate them.

After you’ve chosen the specific size and style which you want, you should determine how much you need. Make some allowances for waste cutting.

  • Order All the Required Materials
    In the planning phase, you will get a list of all the materials which you require. Besides the moldings, you should order adhesives, caulk, and fasteners as well. To save yourself the hassle of making many trips to the hardware store, purchase everything you need all at once.
  • Assemble the Materials
    Assemble all the materials which you have bought in a work area. While assembling them, confirm if you have everything which you need. If you notice you forgot to get something needed, you should purchase it immediately.
  • Pre-finishing
    Sometimes, it can be quite essential to pre-finish your crown moldings. Pre-finishing is an excellent idea, especially in instances where you intend to utilize brightly colored paints in your installation process.
  • Layout
    Draw a distinct solid line around the room where you would install it. The distance between this line to the ceiling will be the height of it.

This line should be straight. Then, draw another line on your ceiling to mark the projection. Use these two lines to mark the ceiling joists and the wall studs.

  • Start Installing
    Start the installation process from the least noticeable corners. Wood moldings are usually lapped at straight joints and cropped at inside corners.

However, this is not the case in polyurethane molding. When installing this molding type, miter cut both the inside and outside corners; and utilize straight butt joints.

You should cut crown molding when it is turned upside down. Dry fit each piece of the molding before applying adhesive to it. You can utilize finish nails to attach the molding.


Guide to Installing a Garden Fence

Types of Garden Fencing

Featheredge garden fencing is composed of overlapping timber vertical boards. This is the heaviest and sturdiest type of panel, providing you excellent privacy. It’s also great for fencing.

Waneylap fencing is composed of overlapping timber horizontal boards, a less expensive fence that provide high level of privacy.

Trellis fencing could be used on its own as a decorative panel on top of a solid fence, or as an open screen fencing.

Palisade garden fencing provides visibility as well as good security in the form of a typical picket-style fencing.

Fence Posts

The next step to take is choosing the right fence posts. Concrete and wood fence posts both have their own advantages and disadvantages. Concrete posts ensure a sturdy fence, however they do require a lot of work, while wood fence posts are a lot easier to handle. But because they are buried under the ground, they’re prone to rot.

Fence Height

Next, decide on your fence’s height. Work out post length before you calculate the number of panels you’ll need. It’s best to treat your panels with some sort of all-purpose preservative.

Before building your garden fence, use a string to mark your boundary line. Treat the area with a weed killer and clear away any vegetation, and then lay out your fence posts evenly along the string.

After checking the location of power cables and water pipes, use a metal spoke, bar or rod to make a line of evenly spaced holes. The post holes must be three times as wide as your post and should be two-feet deep. Once your posts are in place, provide a support to the end of each post by packing brick or stone hardcore into the hole’s base.

Then fill each post hole with water halfway and then pour the concrete mix. When concrete reaches the level of the ground, slope the concrete away from the fence post so water will run off. With a spirit level, check is your post is vertical on both adjacent sides, and then prop it up with one to two wood battens in order to hold it in position while the concrete mix sets. Allow the concrete mix to harden for at least one hour, before you attach your fence panels.

Once it’s dry, screw your panels to your posts using two to three post clips for each panel. Add concrete gravel or treated fence boards along the bottom, or place a gap at least four inches to keep the panels off the ground and prevent rot. Finally, screw your fence panels to your posts using two to three U-shaped post clips on each post.


Building a Fence

Important Things To Do

Observe property lines. Never risk having to put down your fence by going even an inch over your boundaries. Review the blueprint of your house or line drawing or obtain a new survey from your land surveyor to be sure of the boundaries. Fence contractors often install a foot inside the property line, to ensure that they build on the safe side.

Respect the limits. Fence builders get necessary permits and should be aware of regulations of local zoning on height of the fence, setbacks, distance from a street, and other building restrictions. Typically, height limits are six feet for the back and side yards, four feet for the front yards. Often, there are more restrictive rules that apply to the corner lots, where blind curves could limit visibility of drivers. To avoid any dispute, ask about restrictions before you choose the type of fence to construct.

Observe the HOA rules. It’s your job to know the do’s and dont’s of home owners associations (HOA), not the fencing contractor. To avoid suffering from committee wrath, engaging in a dispute, it’s important to observe HOA guidelines. These guidelines could dictate the fence height, style, and maintenance.

Nice Things to Do

Share the plans you have regarding your fence. Nobody likes unpleasant surprises; so before building a fence, save yourself a dispute and talk to your neighbours. If there are already issues regarding boundaries, be sure to resolve them before building a fence. You do not have to show them the design you want for your fence; it will only invite trouble. They simply have to live with your personal choice unless it poses danger or reduces property values.

Put the best fence face outward. Putting the more finished side of the fence on the yard of your neighbour or facing the road is a common practice.

Maintain. It is your responsibility to clean and take care of both sides of the fence. If a section starts to age and lean, make necessary repair or simply replace it.

Good Things to Know

The word “fence” includes hedges and trees that make barriers.

If you have a compelling reason for wanting to erect an extra high fence, to block a noisy street, or an unsightly view, apply to your local zoning board for variance. Your neighbours can comment regarding your request during the hearing.


Balinese Decor Ideas

Open Space Home Design

Bali is a beautiful island where you can visit various beautiful tropical beaches like Sanur and Kuta. The house will reflect the beauty and warmth of Balinese beaches if it has high level of natural sunlight, sandy coral wall color and dramatic outdoor views. Let the breezy air flow inside the room. Plan the house in open space design. The boundary of indoor and outdoor areas should be limited. The large glass walls or glass sliding doors in the living room allow the occupants to enjoy the exquisiteness of outdoor area. If you do not mind to have a full remodeling project, integrate the home with stylish terrace, skylight and beautiful courtyard.

Natural Materials And Finishes

Balinese home is not great if you dominate the space with synthetic materials. Look for the natural materials and finishes. The furniture pieces like coffee table should be refined in brown undertones. Stimulate the exotic feeling with dark brown chocolate finish on the teak wooden table. If it is very difficult to get teak furniture, pick bamboo furniture as the alternative. It is cheaper than teak. The elements of the house such as window coverings, tabletops, flooring and room dividers can feature paper, stone, wicker, tile, metal or rattan material.

Balinese Color Schemes

Don’t be afraid to mix and match bold and bright colors to incorporate Balinese atmosphere. A lime green tone on focal wall creates refreshing ambiance. The bold tangerine sofa is perfect to spot at the corner. Put floral printed throw pillows on the sofa. If you want a striking outcome, the combination of cobalt blue and deep red is worthy to try. The Balinese decor will reflect modern look if you use the combination of pale saffron and vintage white tones. Spread a sisal rug or bamboo mat on the dark finished wooden floor for the finishing touch.


Plasterboard Fixing For Home

Common plasterboards are usually offered in square edge or tapered edge. The tapered edged boards are great for skimming or joining while the square edged boards are best for textured finishes. The sheets are generally in 1200mm to suit 600mm stud spacing that is common with houses today. You can however find other widths to match with your individual specifications. The standard ones have brown face and an ivory face. The ivory face is for plastering and plaster should therefore be kept off the brown reverse side or face. Plasterboards are very popular with new homes and even old homes. It is probably because of the benefits and advantages they come with.

The Advantages

  • The boards help in preventing fire from spreading rapidly. This is because the gypsum is made of crystals that contain small water amounts also referred to as water of crystallization. In case of a fire, the water is pushed off greatly helping in keeping the temperatures down. It means that the boards can be used for fire protection. In special multi layered system applications, the boards can offer fire protection for several hours.
  • The plasterboards are also great at cutting down the noise. They deter the transmission of airborne sounds like music and speech. You will actually find boards that have cores designed to offer better sound insulation.
  • Wallpaper can be applied directly onto the boards to create a beautiful interior hence you are not limited to the natural look of the boards. It is, however advisable to seal the boards first so it is easy to strip down the wallpaper whenever the need arises. The boards also give you the liberty to paint to achieve your desired look.
  • The boards are easy to cut and are readily available. It makes it possible for you to handle your DIY projects with ease when you know what you want.
  • They are sagging resistant, but flexible at the same time, so you can have an excellent finish for a long time.
  • These boards are easier to put up compared to plaster and they can be recycled.


Desk Lamps

Adjustable-neck lamps

These units are ideal for people who constantly adjust the level of light. The lamps are fitted with a weighted base so that they sit firmly on the desk surface. To allow flexibility, the lamp’s neck is fitted with multiple hinges or telescoping spines.

Wall-mounted lamps

These units are characterized by a base that is mounted with screws directly into the wall. The lamps have a flexible or hinged neck that gives them freedom of movement. These units are ideal for homes with curious pets and young children.

Bankers’ lamp

The lamp is designed for aesthetic purposes. The unit is completely stationary and often sits on the back center of a desk. While the lamp provides lighting and increases the appeal of a desk, it’s not meant for computer desks. This is because the computer’s screen tends to block the lamp’s light.

Buying the lamps

For you to get the benefits of the units, you need to buy the right ones. This calls for you to consider your needs. Since the lamps are designed to provide light for different purposes such as studying, reading, and hobby work, you should ensure that you buy a unit that has the right light capacity that will match the intended purpose.


Types of Siding for Homes

Vinyl

Vinyl, originally introduced in the 1950s, is easily the most common type of material used today. It is popular because it is highly versatile, inexpensive, and resistant to various kinds of damage. For those on a tight budget, vinyl is oftentimes the best choice. Also, a basic cleaning is all it takes to make it look like new again.

Aluminum

Aluminum is excellent for any structure as it is extremely durable, lightweight, and resistant to severe weather and insect damage. In terms of maintenance, it does not get much easier than aluminum. All a person needs to do is clean it once or twice a year with soap and water. Aluminum is also a great insulator, which can help reduce energy usage; and it is perfect for use in any home design, from rustic to modern.

Brick

For homeowners who are interested in choosing a siding solution that is built to last a lifetime, brick may be the perfect way to go. In addition to being structurally solid, brick can withstand insect damage and is one of the most fire-resistant building materials available. It also offers a highly distinct feeling of permanence and status, which is what drives many to this material as they think about the overall atmosphere they would like to achieve with their property.

Wood

Wood is a time-honored siding choice that has been popular for countless years, and for good reason. Wood offers unlimited flexibility in terms of design. It is easy to customize with any shade of paint or stain, all without taking away from that beautifully natural look that only real wood can create. While it requires considerably more regular upkeep when compared to other common materials, this bit of extra work is considered to be well worth the effort by many.